Getting Started with IPM . It includes the following major sections. If you have installed the IPM server and client on the same workstation, then you can start the IPM database server, IPM server, and IPM client using a single command. You can also start the IPM client server and client separately. To start the IPM client on a different Solaris workstation from the IPM server, enter the following commands. CSCOipm. Client/bin. To start the IPM client on a Windows NT workstation, follow these steps. Step 1 Make sure the IPM server that you are connecting to is running on a UNIX workstation. As you configure collectors, they are displayed in this window. Each collector is a combination of a configured source, a target, and an operation. For each collector, you specify parameters for gathering statistics, generating event notifications, and scheduling. This release provides central services and database functions on an IPM server that communicates to multiple IPM clients. You can install the IPM client software on the same workstation as the IPM server or on a workstation that is on the same network as the IPM server. A collector is a definition of a source router, a target device, an operation, and a collector schedule. Each source router must contain the Cisco IOS software RTR feature. For information on configuring SNMP on the source router, see the . The Source Router window () is displayed. The Add Source Router window () is displayed. This host name can be from 1 to 6. This value can be from 1 to 3. The default value is public. This value can be from 1 to 3. IPM attempts to locate the router and determine whether or not it is SNMP enabled with the correct community string. If the router is successfully located, IPM adds it to the Source Router window. If IPM cannot reach the router, IPM displays an error message and redisplays the Add Source Router window. For information on modifying or deleting source routers, see the . This chapter provides information about starting the IPM application and configuring a collector to gather latency data. It includes the following major sections. Compendium of IPM Definitions (CID) What is IPM and how is it defined in the Worldwide Literature? Bajwa and Marcos Kogan Integrated Plant Protection Center. Starting an IPM Program. Integrated pest management (IPM) is the practice of combining knowledge of the pest and host plant with multiple tactics for long-term, safe. A target can be an SNA host or any IP- addressable device. The Target window () is displayed. The Add Target window () is displayed. The possible values are. Requires a destination IP address or host name. Requires the host name defined for the SNA PU connection to VTAM. Requires the host name defined for the SNA PU connection to VTAM. Requires the host name defined for the an SNA PU connection to VTAM. This is the name that appears in the Target field when you define a collector. This is the name that appears in the Target field when you define a collector. If you omit this value, default session parameters are used when communicating with the NSPECHO application running on the mainframe. If you omit this name, the SNMP agent in the source router sends a name of all blanks to the SNA host, which then uses a set of default session parameters for the echo session. IPM closes the Add Target window and the newly defined target is added to the list of defined targets in the Target window. For information on modifying or deleting targets, see the . Use one of these operations when you define a collector. You can also define one or more new operations to fit your needs. For information on defining a new operation, see the . The Add Collector window () is displayed. The collector that you defined is displayed in the list of collectors in the IPM Main window. For information on viewing or deleting collectors, see the . You view the response- time results from any of the collectors listed on the IPM Main window and see whether or not that collector is active or inactive. This data is only displayed in real time, it is not stored in the IPM database. The Real Time Display window () is displayed. Data points will be added to the graph for each interval that the response time is measured for the selected collector. The Time Filter window () is displayed. These times relate to when the statistics are gathered by the collector, not when you want to view them. When this window is displayed, it already contains the starting and ending times for the collector, so you can press Enter to view statistics for that time period. This marks the earliest statistics you want to view. For example, although your collector gathered statistics from 1. In this case, you would indicate 1. If you use this method, you must enter the date and time completely using the correct delimiters. For example, if you enter a starting time of 1. For example, although your collector collected statistics from 1. IPM- Institute of People Management (011) 544 4400 or (011) 0662351. As you finish your degree program, you may be looking for ways to build leadership read more.In this case, you would indicate 1. For example, if you enter an ending time of 1. Choose one of the available options: Hourly, Daily, Weekly, or Monthly. The Response Graphs window () is displayed. The response- time statistics for that hop are displayed in the Response Graphs window. If printing to a printer, specify the name of the printer. If saving to a file, specify the directory and filename.
Support Getting Started with IPM. The chapter provides information on starting the IPM. Step 2 Open the Cisco Internetwork Performance Monitor 2.0 program. A confirmation window () is displayed. Active collectors will continue to run and gather response time data. To shut down the servers, use the ipm stop command. To stop gathering data, stop the collectors before exiting the IPM client. The collectors remain on the routers until you uninstall the IPM software.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. Archives
January 2017
Categories |